to send classified
**** Sellers - please be
aware of cashier check fraud ****
Sale: ACD 3 speed air shifter,
controller and Quarter stick for reverse pattern 400.00
Richman 9" ford pro 4.10 150.00
Richman 9" ford street gear 4.56 75.00
Datona pinion support Aluminum 50.00
Strange steel 28 spline 9" yoke 75.00
Millidon BBC dragster oil pan and pick up 150.00
Moroso 3 qt. Accumlator, brackets, remote on/off valve 200.00
Mallery 110 fuel pump and filter 75.00
510 CI BBC rotating assamble, Scat 4340 4.250 stroke
Eagle h-beam rods W/ ARP 2000 bolts
Weisco 14.5 to 1 dome
2 bolt main stud kit, ATI super dampener,vTCI flex plate, oil pan stud kit, aluminum timming cover, timming pointer, Clovies double roller hex-adjust 500.00
All parts are used, I have other BBC parts roller lifter etc.
Call Matt at 320-249-3258
Sale: For Sale SB steel roller tip 1.6 rockers set of 16 $50.00
Hoosier Slicks 29.5/11.5w-15 one season left $50.00
Strod parachute black $50.00
Air shifter kit with bottle and gage $50.00
TCI trans bk. solenoid new never used paid $95 sell for $50.00
MSD 3 step activator $25.00
Holley 650 race carb. 50cc pumps adjustable linkage jet extensions no choke tower $100.00
Alum. beefed up power glide, new rebuild never used $300.00
Turbo 350 core for rebuilding $150.00
Bill Rauch 218-343-1239 or 218-365-3150 firstname.lastname@example.org
For Sale: 1970 Plymouth Cuda, was built to run nhra super
gas. Back half car built by Alston Chassis Works in the mid 80's.
The car is apart but I have all the parts and pieces to put it
back together plus some extra parts and tools that go with it.
Including a 500 inch engine and a 727 trams with brake and two converter
choices. Dana 60 has 456 gears in it plus I have a set of 513's
used out of this rear end. The engine is not together but the
machine work is done and I have new rings, rod and main bearings,
the cam bearings are installed, three timing set ups, std double
roller, cloyed adj double roller (new) and a used miladon gear
drive. The pistons are used as are the Manley h beam rods. Rack
and pinion steering, a arm front suspension with adj coil over
shocks. Rear is ladder bar, leaf spring with rotators and adj qa1
shocks. If you have a youngster coming out of jr. Dragster this
would make an awesome starter car. It drives as easy as any car
could. My name is Randy and my # is 1-320-766-2078. I will listen
to all offers and trades. You will never know if you don't ask. I
have a soft spot for the kids!!!!!
Yes looking for 1977-81 Camaro z-28 or ? Drag car or street car no junk cars
please color not important, prefer auto trans, will look
at stick cars also, motor not there is
ok, call before 8 pm 507.387.2086.
A Hurst-Olds prefer 1983-84 will look at others or w-30 w31 442 olds cutlass call
507-381-0831 Drag Cars or Driver Quality car thanks.
1967 Camaro Drag Car, Turn-KEY!! Set-up for bracket and
S/G, full electronics.
Car runs consistent 6.10s and 9.20s on 1sec throttle stop
setting. Car has been fully prepped for next season, but
now changing direction to move to a Top Sportsman car. Get
in, push the button, go racing.
Full tube frame with Strange strut front suspension and outlaw
ladder-bar rear with 4.55 Dana60, 35spline axles. Strange
DA shocks (rear) just rebuilt Jan 2014. Car weighs 2800#
fully wet with 200lb driver. Current 8.50 nhra
Motor is 540ci BBC by Moran Motorsports1150 Dominator carb
rebuilt Dec 2013 by APD. Heads are Dart Pro1 325, ported
with Jomar girdle. 14.8 comp, JE gas ported custom cut
pistons, Lunati 4340 pro series crank with Eagle rods, 4-7 swap
Mike Moran roller cam with hex-adjust timing chain. Moroso
vacuum pump, Meziere elec water pump, shogun mini alternator,
east coast electric high torque starter, JW “the wheel” flex
plate, 10 pitch. Custom 12degree step headers. Pulls
hard to 8200rpm—but car has been slowed down (gearing and
throttle stop) to roll thru ¼ mile traps at 7400rpm.
Transmission is T400 with hardened parts—freshened Jan 2014.
Hughes ProVI converter, 5200rpm stall. CSR carbon fiber
Please call for pics or to see. Car is kept in a heated
shop throughout winter--easy to take a look at. Also
posted on craigslist and racingjunk (with many pics).
Wiring harness for
68 nova. Harness from 67 to 72 G.M. will work. please contact me
1970 Olds Rallye 350--Ram Air, wing, 12 bolt rear end open, Blk
interior with factory bench seat, Paint 2yrs old Base coat clear
coat, Car is nice I took it to car shows CAR CRAFT etc, Stock
motor-trans weld rims 15", new bumpers, take trades What ya
got? asking $11.500 507-381-0831 email@example.com